Search Results for: t1 Extenders

DCB DSU, Digital Transmission

T1 and E1 Products made by DataComm For Business — DCB

T1 Extender
DA-56 DA 56 Async DSU
E1  E-Extender

T-Monitor T1 Line Monitor
O9310 Optical Multiplexer with 4 T1 interfaces, Single Mode Fiber, AC and DC Power
V4300 Mini DACS, T1 to E1 Converter with 2 T1 or E1 ports, SNMP AC Power
V4300-T1 or V4300-E1 Additional T1 or E1 Interface
T-2500-DCE Single Port T1 CSU/DSU with DCE Interface
H3300 T-1 Extender Over Two or Four wires for Long Distance, DSL Transport

T-1 Extenders

IP-6700 1 to 4 T1s over IP TDMoE
iThe IP-6700 is designed to transport one to four E-1/T-1/DTE/DS-3 signals with timing plus Ethernet traffic over the IP network. This is a cost effective way of migrating to an IP network from existing voice and data networks using existing TDM based equipment.

IP-6704A
1 to 4 T1s over IP TDMoE
imgimg The IP-6704A is designed to transport 4 E-1/T-1/DTE/DS-3 signals with timing plus Ethernet traffic over the IP network via Pseudowire protocol. This is a cost effective way of migrating to an IP network from existing voice and data networks using existing TDM based equipment and SATOP, CESoPSN, or MEF8.

IP-6716
Up to 16 T1s over IP TDMoE
imgimg The IP-6716 transports up to 16 E-1/T-1/DTE signals with timing plus Ethernet traffic over the IP network via Pseudowire protocol. This is a cost effective way of migrating to an IP network from existing voice and data networks using existing TDM based equipment and SATOP, CESoPSN, or MEF8.

IP-6750
1 to 16 T1s over IP TDMoE
imgimg The IP-6750 transports up to sixteen T1/E1 lines and up to 8 Gigabit Ethernet traffic over a carrier ethernet network using TDM Pseudowire Protocol. This is a cost effective way of migrating to a carrier ethernet network from existing voice and data networks using existing TDM based equipment while taking advantage of Ethernet Ring Protection switching or ELPS.

T-1 Extender
A genuine T1 repeater. No setup, no software; just extends the T1 demarc up to 5,000 ft (or more with intermediate units) with reliability at low cost.

O-9310 T1 Via Fiber
imgimg The O-9310 extends up to four T1 lines over a single pair of fiber for only $939. The economical solution when there is fiber available.

MD-400 T1 Extender
The CXR MD-400 extends a full T1 / E1 over copper pair up to six miles (10.2 KM) or fractional T1 / E1 up to ten miles (17.2 KM). This is a new generation, cost effective G.SHDSL modem that extends a T1/E1 interface over very long distances.

Data Connect offers a full range of industrial WAN products designed for rough and tumble environments.  Here you will find INDUSTRIAL SWITCHES, T1 EXTENDERS, ETHERNET EXTENDERS, INDUSTRIAL MODEMS and more.

DCE SE2130 Serial Ethernet Bridge
Ethernet Extenders
Industrial Ethernet Switches
Starcomm
T1 Extenders
Modems
DCE FT1 Series T1/FT1 CSU/DSU
ADSL2+ DSLAM
VDSL2  ADSL2+ Combo IP DSLAM

Data Connect Enterprise is a manufacturer of reliable networking and network connectivity products. Founded in 1988 the company specializes in commercial, carrier and industrial grade network extension, network edge, and access solutions.

Data Connect is well known for its reliable ADSL and VDSL access solutions, Ethernet servers, switches, and extenders, wireless modems and routers, VoIP solutions, POE products, channel bank and T1/E1 solutions, and a very broad range of commercial and custom designed wireless and wire-line modem and network extension products for trailing-edge, leading-edge, and blended migration applications.
Data Connect offers solutions for both wire-line and wireless applications addressing data, voice and video transmission needs. We are well equipped to help businesses, service providers, carriers, VARs, and systems integrators looking for reliable networking solutions. Ask Data Connect how we can help you with both your legacy network applications and your new network requirements.

DCE/FiberT Fiber T1 Extenders

This product will extend a T1 across multimode fiber up to 2KM.  Models for greater distances and for single mode fiber are also available. 

Simply set up one DCE Fiber T1 Extender at each end of your fiber run, and you are set to go.

Standards: T1: ITU-T G.703, G.704, AT&T TR-62411, ANSI T1.403

Interfaces: RJ48c 100ohm balanced T1 connector and dual SC 155M fiber port
Operating wavelength: 1310nm multimode
Operating distance: 2Km on 62.5/125um fiber, works also on 50/125um fiber
Optical connector: SC dual type (versions with ST or FC optical connectors are available on request)
Front LEDs: Power, Fiber Link, T1 Link, Test mode
Power: External 90-260V AC switching adapter 9VDC@1A with NEMA1-15(2 blades only), US type main plug
Temperature:” 50°C (Operating); 70°C (Storage)
Humidity: 20” 80% non condensing (Operating); 90% (Storage)
Consumption: less than 5W
Dimensions(WxDxH): 85.6mm x 122.6mm x 20mm
Weight: 310g (without AC adapter)
Compliance: CE, FCC Class A
MTBF: 65,000 hours

We have units that will extend multiple T1’s over fiber
We have units that will extend a T1 over copper

Network Extension Products

DCE Express specializes in Ethernet Extenders, T1 Extenders, SCADA Modems, Serial Data Hardware, VoIP gateways, connectivity products, CTC fiber solutions and DSL products products.

CALL 301-924-7400 For pricing and availability — or to order.

We are part of Data Connect Enterprise and of course, we carry Data Connect products.  Data Connect is well known for its reliable ADSL and VDSL access solutions, Ethernet servers, switches, and extenders, wireless modems and routers, VoIP solutions, POE products, channel bank and T1/E1 solutions, and a very broad range of commercial and custom designed wireless and wire-line modem and network extension products for trailing-edge, leading-edge, and blended migration applications.

We feature products made in the USA by Patton Electronics:

Bonding Load Balancing Wireless Routers
Connect-IT Products
DSL CPE
G.703 Baluns
Ethernet Extenders
OnSite Products
Patton RAS
Patton ForeFront DSLAM
Patton ForeFront Chassis
Serial Communications Devices
Surge Protectors
T1 Bridges
T1 Extenders
VoIP Gateways and Routers

We feature products made in the USA by DCB

Broadcast Polling FRAD
Conitel to Async Protocol Converter
DCB PSU-08 Poll Sharing Unit
DCB Remote Access
DSU & T1 E1 Products
Encryption and Security
Ethernet Switches
Ethernet-Extender
EtherPath
Modem Sharing
DCB IP-6600 Routers
SCADA Multidrop Mux
SR Multiplexers
Voice Adapters

Featured Products

If you need to extend Ethernet over copper to distances as great as 6 miles consider the Patton bonded pair Long Range CL2304 Ethernet Extenders:

And if you need to extend a T1 Demarc over copper or fiber, then consider T1 Extender Solutions

If you are looking for legacy modems, we carry them all, including our own Industrial Grade 202T Modem, the Data Connect IG-202T.

Check out our PoE Ethernet Extenders which enable the distant unit to power itself from the local unit, and provides about 15 Watts of power to its PoE Ethernet interface.

T1 Extender
2115/EUI-2PK CopperLink-T 2 pack

The Patton 2115 T1 Extenders are the perfect choice for enterprises, integrators, and service providers needing to extend T1 and E1 circuits beyond their typical reach while conserving the number of wire pairs used.

With the CopperLink–T extenders, zero configuration is required. They operate in clear-channel mode, thereby facilitating the transparent extension of data and voice bearing circuits including the F-bit on T1 circuits. The two active pins on the RJ connector are polarity insensitive, so you don’t even need to worry about which wire you connect on the line interface. Simply take them out of the box, put them on either side of the dry copper pair, connect your T1 or E1 device and the circuit will light up immediately!

For these reason, the CopperLink–T extenders are the ideal solution for most popular applications such as T1/E1 backhaul from a remote site, T1/E1 relocation, T1/E1 extension across a campus or between buildings, and last-mile TDM delivery.

The CopperLink–T simplifies transparent T1 extension.
Plug-and-Play–units automatically link up when placed on opposite sides of a dry copper wire pair.
Units operate in clear channel mode to easily transport voice and data (F-bit included).
Uses only wires on the link.
Link interface is polarity insensitive to make connection to the twisted-pair wires easy.
Intuitive LEDs help you quickly troubleshoot line and circuit problems.

Patton 2115 T1 Extender: Single female RJ-48C
Supported Line Tests: V.52 511/511E Pattern Generator with RDL; LAL
Clocking: CO unit preset for Network Clock, CPE unit preset for Receive Recover
Line Coding: 16-constellation TC-PAM
Line Interface: Female RJ-11 using pins 2 & 3; Two wires (single twisted-pair)
Front Panel Indicators: Power–Solid green indicates unit is powered up. Slow blinking indicates unit is in POST. Fast blinking indicates unit failed POST. Dark indicates unit does not have power.
Link–Solid green indicates end-to-end link. Flashing indicates unit is training. Dark indicates link is down.
Frame–Solid green indicates valid framing. Flashing indicates signal being received, but no link established.
Power Supply: External power supply options: Universal 90-260 VAC operating from 50-60 Hz; 120 VAC/60 Hz; 240 VAC/60Hz; -48 VDC
Compliance: FCC Part 15A, CE Mark, EMC Directive 89/336/EEC, Low-Voltage Directive 73/23/EEC
Environment: Operating Temp.: 32-122°F (0-50°C)
Humidity: 5-90% non-condensing
Dimensions: 4.7 x 1.52 x 5.0 in. (10.6 x 3.9 x 12.7 cm)

Patton_ 2113_2115_Manual

• E-1 4-wire repeater
• Extends in-house E-1 lines
• Up to 4000 feet between units
• RJ-45 or screw down connectors
• Simple connection to a 4-wire line
• Inexpensive solution to long cable runs
• 120/240 VAC, 12/24/48, or 125 VDC powered
• 1U high rack mountable; 1,2, or 3 x19″ rack
• 20 slot chassis option

The DCE Copper-E is a 4-wire repeater for use on customer-owned lines or to extend telephone company demarcs. The E-Extenders are normally used in pairs to extend in-house E-1 lines in campus and highrise environments.

Each pair of E-1 Extenders may be located up to 4000 feet apart. The Extender circuitry is rated to -43 dB dynamic range at the E-1 rate of 2.048 Mbps. As implemented, the parts are slightly de-rated to provide long life at extended temperature range. Therefore the distances specified in this document are only 4000 feet. Solid copper 22 or 24 AWG, two twisted pair is the preferred cable for connection between the Extenders. Connection to the Extender is made through RJ-45 modular connectors or 4-wire screw down barrier strips. Each Extender comes standard with two screw-down barrier strips and one RJ-45 connector. If only RJ-45 connections are desired, extra RJ-45 adapters (part number 9502122) may be ordered.

The 120/240 VAC E-Extenders are powered by a small wall-mount transformer. The Extenders are designed for connections between E-1 equipment such as PBXs, E-1 multiplexers, E-1 line drivers, CSUs, routers or any other E-1 equipment requiring long customer owned cable runs. E-Extenders may be used to connect this equipment across a campus, between floors of a high-rise office building or between office buildings with underground cable runs. The E-Extenders are transparent to the type of data sent over the E-1 link. The data can be D-4 format, ESF, PRI, G.703, G.704, etc.

The Extenders are most often used in pairs to extend a telephone company demarc. For example, if a CSU or DSU is limited to 655 feet and is connecting to a phone company smart jack demarc which is limited to 655 feet, the E-Extenders are used in pairs to extend that distance up to 5000 feet.

To install, simply connect the transmit pair of one Extender to the receive pair of the other Extender. Pairs are not polarity sensitive.   Units are supplied with 2 screw down connectors and 1 RJ-45 connector.

A cable cross-over is required between two Extenders if using straight RJ-45 cables. This cable connects the receive pair to one Extender to the transmit pair of the other Extender.

Patton CL1214 CL1214/EUI-2PK
Ethernet Extenders

The CL1214 extenders are used primarily in high bandwidth, short distance applications. Combining data flows from up to four network-enabled devices onto a single twisted pair or coax cable, the CL1214 can deliver IP traffic up to 4,250 ft (1295 m) away, well beyond the standard 328-foot (100-meter) Ethernet distance limitation.

Ideal for bandwidth-intensive applications the CL1214 delivers remarkable symmetrical line rates greater than 100 Mbps. Best of all, like all CopperLink products, the CL1214 leverages existing copper infrastructure to deliver high speed Ethernet connectivity over voice-grade twisted pair, Cat 5e/6/7, and new to the CopperLink line, coaxial cabling.

Realize fiber-like speed and distance without the expense of fiber with Patton’s Ultra-High-Speed CopperLink Ethernet Extenders.

A built-in 4-port Ethernet switch makes the CopperLink Model 1214 ideal for delivering multiple IP information streams over a single cable. For example, at a guardhouse or security kiosk, you could aggregate IP data from a laptop, a motion sensor, and two high resolution IP video cameras for simultaneous transmission over a single Ethernet connection.

Combining data flows from up to four network-enabled devices onto a single twisted pair or coax cable, the CL1214 can deliver IP traffic up to 4,250 ft (1295 m) away, well beyond the standard 328-foot (100-meter) Ethernet distance limitation.

With achievable line rates up to 100 Mbps, the CopperLink 1214 eliminates the bandwidth constraints commonly experienced with other copper-based transmission technologies. The Model 1214 is engineered to re-use existing infrastructure previously employed in legacy applications including alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV. Many newer cabling standards are also supported, including Cat 5e, Cat 6 and Cat 7.

Four user-selectable configuration profiles combined with Patton’s auto-rate adaptation feature ensure maximum achievable symmetrical or asymmetrical rates for the installed noise environment, wire gauge/type and length.

Symmetrical line-rate settings are ideal for such applications as remote LAN extension, video teleconferencing, and data backhaul. Asymmetrical configurations are well-suited for applications requiring higher downstream speeds and/or longer distances between Ethernet devices. Typical symmetrical scenarios include medical imaging, livestock monitoring, underwater video, internet gaming, and transporting high-resolution IP video from security cameras.

Patton CL1214/BNC/EUI High Speed CopperLink Ethernet Extender; BNC Line, 100-240VAC

Patton CL1214/BNC/EUI-2PK High Speed CopperLink Ethernet Extender Kit (Local and Remote); BNC Line, 100-240VAC

Patton CL1214/E High Speed CopperLink Ethernet Extender; RJ45 Line, No Power Supply

Patton CL1214/E-2PK High Speed CopperLink Ethernet Extender Kit (Local and Remote); RJ45 Line, 100-240VAC

Patton CL1214/EUI High Speed CopperLink Ethernet Extender; RJ45 Line, 100-240VAC

Patton CL1214/EUI-2PK High Speed CopperLink Ethernet Extender Kit (Local and Remote); RJ45 Line, 100-240VAC

Patton CL1214/S/EUI-2PK High Speed CopperLink Ethernet Extender Kit (Local and Remote); RJ45 Line; POTS; 100-240VAC

Patton CL1214/TB/EUI High Speed CopperLink Ethernet Extender; Terminal Block Line, 100-240VAC

Patton CL1214/TB/EUI-2PK High Speed CopperLink Ethernet Extender Kit (Local and Remote); Terminal Block Line, 100-240VAC

Patton CL1214/TB/S/EUI-2PK High Speed CopperLink Eth Ext Kit (Local and Remote); Term. Block Line, POTS Port; 100-240VAC

Extended Temperature Ruggedized CL1214E

Typical installation on the line side:

CL1214 USER MANUAL

Data Connect Copper-T
T1 Extender

The Data Connect Copper-T is a T1 demarc extension device or T1 repeater. This simple unit allows T1 DSUs, channel banks, routers, and PBXs to be located up to 5000 feet from the telephone company’s demarc. With T1 lines becoming more common in the business and school environment, this is a lifesaver in campus and high-rise environments. The Data Connect Copper-T is powered by a small wall-mount transformer or optional DC power supply, and is used for connections between T-1 equipment such as PBXs, telco demarcs, T-1 multiplexers, T-1 line drivers, T-1 local multiplexers or any other T-1 equipment requiring long customer owned cable runs. Data Connect Copper-Ts can be used to connect this equipment across a campus, between floors of a high-rise office building or between office buildings with underground cable connections.

T-1 4-wire repeater
Extends in-house T-1 lines
Up to 5000 feet between units (depending upon cable)
RJ-45 or screw down connectors
Simple connection to a 4-wire line
Inexpensive solution to long T-1 runs
120VAC, 48VDC, or 24VDC powered

RJ-45 adapter or screw terminals may be used in either or both ports. Unit supplied with two screw terminals and one RJ-45 adapter.

Note: This product is NOT intended for 10BaseT or Ethernet. T1 modulation is designed for use with twisted pair solid wire phone cables. The Data Connect Copper-T does NOT extend ethernet connections… only T1 connections. For Ethernet Extenders go here.

Each pair of Data Connect Copper-Ts may be located up to 5000 feet apart.  Solid copper 22 AWG two twisted pair is the preferred cable for connection between Data Connect Copper-Ts. Smaller wire sizes will reduce the functional distance between Data Connect Copper-Ts. Connection to the Data Connect Copper-T is made through RJ-45 modular connectors or 4-wire screw down barrier strips. Both types of connectors are standard on the Data Connect Copper-T.

The Data Connect Copper-T is powered by a small wall-mount transformer, and is used for connections between T-1 equipment such as PBXs, T-1 multiplexers, T-1 line drivers, T-1 local multiplexers or any other T-1 equipment requiring long customer owned cable runs.

Data Connect Copper-Ts can also be used to extend the distance between any T-1 equipment (DSU, channel bank, router, etc.).

The Data Connect Copper-Ts are best used in pairs. If you have a T1 CSU that is limited to 655 feet, connected to a device limited to 655 feet, and you put the Data Connect Copper-T at one end, the Data Connect Copper-T will drive the extra distance. However, the far end device will still be limited to 655 feet and will not likely have sufficient “drive” to reach the far end. The T1 transmitted signal is the issue addressed by the Data Connect Copper-T, so in this case, the line would be error-prone or possibly only work in one direction.

9500095 Customer to demarc RJ45 cable
9500099 Customer to customer T1 RJ45 crossover cable
9502122 Additional RJ adapter
5003011 Additional screw terminal adapter
9902095 19″ rack shelf for 1 to 3 Data Connect Copper-Ts

NOTE : Cable should be Category 3, 2 twisted pair, shielded.
DO NOT use Category 5 cable.  Proper operation cannot be guaranteed if Category 5 cable is used.

Using CAT5 or CAT6, the transmit and receive pairs are not shielded from each other, making Near End Cross Talk likely. If you can use 2 separate cables of CAT5 or CAT6, putting the TX pair in one and the RX pair in another, that would help greatly. The key, is proper sheilding of the pairs.

Copper-T Manual

The Patton CopperLink CL1212 is a 2-Ethernet-port Ethernet Extender which utilizes Patton’s legacy small form factor, and their legacy 5VDC input voltage.  These are Patton’s answer to customer’s who didn’t like Patton’s larger standard, CL1214 devices which run on 12VDC and have become our best selling Ethernet Extenders.

Combining data flows from up to 2 network-enabled devices onto a single twisted pair or coax cable, the CopperLink Model CL1212 can deliver IP traffic up to 1.8 miles (3 km) away—well beyond the standard 328-foot (100-meter) Ethernet distance limitation.

With achievable line rates up to 168 Mbps, the CL1212 eliminates the bandwidth constraints commonly experienced with other copper-based transmission technologies. The Model 1212 is engineered to re-use existing infrastructure previously employed in such legacy applications as alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV. Many newer cabling standards are also supported, including Cat 5e, Cat 6 and Cat 7.

A built-in two-port Ethernet switch makes the CopperLink CL1212 ideal for delivering multiple IP information streams over a single cable. At a guardhouse or security kiosk for example, you could aggregate IP data from a laptop and a high-resolution IP video camera for simultaneous transmission over a single Ethernet connection.

A single-port version, the CopperLink Model CL1211 (available by special order) is ideal for applications requiring the enhanced security of a single Ethernet port.

CL1212/EUI High Speed CopperLink Ethernet Extender; 2 x 10/100BaseTX; RJ45 Line, 100-240VAC

CL1212/EUI-2PK High Speed CopperLink Ethernet Extender Kit (Local and Remote); 2 x 10/100BaseTX; RJ45 Line, 100-240VAC

CL1212/TB/EUI High Speed CopperLink Ethernet Extender; 2 x 10/100BaseTX; Terminal Block Line, 100-240VAC

CL1212/TB/EUI-2PK High Speed CopperLink Ethernet Extender Kit (Local and Remote); 2 x 10/100BaseTX; Terminal Block Line, 100-240VAC

CL1212E/CC/EUI Extended Temperature CopperLink High Speed Auto Rate Extender; 2 x 10/100BaseTX; RJ45 Line Connector; Conformal Coated; 100-240VAC

CL1212E/CC/EUI-2PK Extended Temperature CopperLink High Speed Auto Rate Extender Kit; 2 x 10/100BaseTX; RJ45 Line Connector; Conformal Coated; 100-240VAC

CL1212E/EUI Extended Temperature CopperLink High Speed Auto Rate Extender; 2 x 10/100BaseTX; RJ45 Line Connector; 100-240VAC

CL1212E/EUI-2PK Extended Temperature CopperLink High Speed Auto Rate Extender Kit (Local and Remote); 2 x 10/100BaseTX; RJ45 Line Connector; 100-240VAC

CL1212E/TB/CC/EUI Extended Temperature CopperLink High Speed Auto Rate Extender; 2 x 10/100BaseTX; Terminal Block Line Connector; Conformal Coated; 100-240VAC

CL1212E/TB/EUI Extended Temperature CopperLink High Speed Auto Rate Extender; 2 x 10/100BaseTX; Terminal Block Line Connector; 100-240VAC

CL1212E/TB/EUI-2PK Extended Temperature CopperLink High Speed Auto Rate Extender Kit (Local and Remote); 2 x 10/100BaseTX; Terminal Block Line Connector; 100-240VAC

CL1212E/TB-SKD Ethernet Extender, PCB Sub Assembly, Terminal Block Line; 2 x 10/100; No Power Supply

CL1212E-SKD Ethernet Extender, PCB Sub Assembly, RJ45 Line; 2 x 10/100; No Power Supply

CL1212-Users Manual